PBD::Signal1<void, pframes_t> InternalSend::CycleStart;
-InternalSend::InternalSend (Session& s, boost::shared_ptr<Pannable> p, boost::shared_ptr<MuteMaster> mm, boost::shared_ptr<Route> sendto, Delivery::Role role)
- : Send (s, p, mm, role)
+InternalSend::InternalSend (Session& s,
+ boost::shared_ptr<Pannable> p,
+ boost::shared_ptr<MuteMaster> mm,
+ boost::shared_ptr<Route> sendfrom,
+ boost::shared_ptr<Route> sendto,
+ Delivery::Role role,
+ bool ignore_bitslot)
+ : Send (s, p, mm, role, ignore_bitslot)
+ , _send_from (sendfrom)
{
- if (sendto) {
- if (use_target (sendto)) {
- throw failed_constructor();
- }
- }
+ if (sendto) {
+ if (use_target (sendto)) {
+ throw failed_constructor();
+ }
+ }
init_gain ();
+ _send_from->DropReferences.connect_same_thread (source_connection, boost::bind (&InternalSend::send_from_going_away, this));
CycleStart.connect_same_thread (*this, boost::bind (&InternalSend::cycle_start, this, _1));
}
{
if (_role == Listen) {
/* send to monitor bus is always at unity */
- _amp->set_gain (1.0, this);
+ _gain_control->set_value (GAIN_COEFF_UNITY, PBD::Controllable::NoGroup);
} else {
/* aux sends start at -inf dB */
- _amp->set_gain (0, this);
+ _gain_control->set_value (GAIN_COEFF_ZERO, PBD::Controllable::NoGroup);
}
}
reset_panner();
}
+void
+InternalSend::send_from_going_away ()
+{
+ _send_from.reset();
+}
+
void
InternalSend::send_to_going_away ()
{
// we have to copy the input, because we may alter the buffers with the amp
// in-place, which a send must never do.
- if (_panshell && !_panshell->bypassed()) {
+ if (_panshell && !_panshell->bypassed() && role() != Listen) {
_panshell->run (bufs, mixbufs, start_frame, end_frame, nframes);
} else {
if (role() == Listen) {
/* We're going to the monitor bus, so discard MIDI data */
-
+
uint32_t const bufs_audio = bufs.count().get (DataType::AUDIO);
uint32_t const mixbufs_audio = mixbufs.count().get (DataType::AUDIO);
-
+
/* monitor-section has same number of channels as master-bus (on creation).
*
* There is no clear answer what should happen when trying to PFL or AFL
/* target gain has changed */
- Amp::apply_gain (mixbufs, nframes, _current_gain, tgain);
- _current_gain = tgain;
+ _current_gain = Amp::apply_gain (mixbufs, _session.nominal_frame_rate(), nframes, _current_gain, tgain);
- } else if (tgain == 0.0) {
+ } else if (tgain == GAIN_COEFF_ZERO) {
/* we were quiet last time, and we're still supposed to be quiet.
*/
_meter->reset ();
- Amp::apply_simple_gain (mixbufs, nframes, 0.0);
+ Amp::apply_simple_gain (mixbufs, nframes, GAIN_COEFF_ZERO);
goto out;
- } else if (tgain != 1.0) {
+ } else if (tgain != GAIN_COEFF_UNITY) {
/* target gain has not changed, but is not zero or unity */
Amp::apply_simple_gain (mixbufs, nframes, tgain);
_amp->setup_gain_automation (start_frame, end_frame, nframes);
_amp->run (mixbufs, start_frame, end_frame, nframes, true);
+ _delayline->run (mixbufs, start_frame, end_frame, nframes, true);
+
/* consider metering */
if (_metering) {
- if (_amp->gain_control()->get_value() == 0) {
+ if (_amp->gain_control()->get_value() == GAIN_COEFF_ZERO) {
_meter->reset();
} else {
_meter->run (mixbufs, start_frame, end_frame, nframes, true);
int
InternalSend::set_state (const XMLNode& node, int version)
{
- const XMLProperty* prop;
+ XMLProperty const * prop;
init_gain ();
for (BufferSet::audio_iterator b = mixbufs.audio_begin(); b != mixbufs.audio_end(); ++b) {
b->prepare ();
}
-}
+}