<para>
Alternatively, if you have a projector or TMS that is accessible via
SCP across your network, you can upload the content directly from
-DCP-o-matic. See the preferences in <xref linkend="sec-prefs-tms"/>.
+DCP-o-matic. See the <xref linkend="sec-prefs-tms" endterm="sec-prefs-tms-short"/>.
</para>
</section>
<section xml:id="sec-prefs-tms">
<title>TMS</title>
+<titleabbrev xml:id="sec-prefs-tms-short">TMS preferences</titleabbrev>
<para>
The TMS tab (shown in <xref linkend="fig-prefs-tms"/>) gives some
</para>
</section>
-</section>
+<section xml:id="sec-prefs-advanced">
+<title>Advanced</title>
+<titleabbrev xml:id="sec-prefs-advanced-short">Advanced preferences</titleabbrev>
+
+<para>
+The advanced preferences are shown in <xref linkend="fig-prefs-advanced"/>.
+</para>
+
+<figure id="fig-prefs-advanced">
+ <title>Advanced preferences</title>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="screenshots/prefs-advanced&scs;"/>
+ </imageobject>
+ </mediaobject>
+</figure>
+
+<para>
+<guilabel>Maximum JPEG2000 bandwidth</guilabel> specifies the maximum
+bit-rate of JPEG2000 that DCP-o-matic will allow you to create. You
+are advised to leave this at 250Mbit/s in normal use for maximum DCP
+compatibility.
+</para>
+
+<para>
+<guilabel>Allow any DCP frame rate</guilabel> removes the limits on
+the DCP video frame rates that DCP-o-matic will create. This may be
+useful for experimentation. Again, you are strongly advised to leave
+this unticked for normal use.
+</para>
+
+<para>
+The four checkboxes labelled <guilabel>Log</guilabel> control what
+sort of messages DCP-o-matic writes to its log file when creating a
+DCP. It is useful to leave <guilabel>General</guilabel>,
+<guilabel>Warnings</guilabel> and <guilabel>Errors</guilabel> ticked
+as this makes the log files useful for tracking down bugs.
+</para>
+
+<para>
+The <guilabel>Timing</guilabel> checkbox will enable extra log entries
+to allow developers to investigate and optimize the speed of
+DCP-o-matic. It will significantly increase the size of the log files
+that are generated, so in normal use it is best to leave this
+unticked.
+</para>
+
+</section>
+</section>
</chapter>
<chapter xmlns="http://docbook.org/ns/docbook" version="5.0" xml:lang="en" xml:id="ch-frame-rates">
</para>
<section>
-<title>DCP rate limitations</title>
+<title>DCP frame rate limitations</title>
<para>
-There are some limitations to video and audio rates in DCPs. This is
+There are some limitations to video and audio frame rates in DCPs. This is
complicated by the fact that not all projectors will play DCPs at the
-same rates. It is possible to create a DCP which one projector will
+same frame rates. It is possible to create a DCP which one projector will
play fine, but another (of a different type) will refuse to play, or
even refuse to ingest.
</para>
content.
</para>
+<para>
+If you want to experiment with other non-standard frame rates, you can
+do so by ticking the <guilabel>Allow any DCP frame rate</guilabel> in
+the <guilabel>Advanced</guilabel> tab of the preferences dialogue (see the
+<xref linkend="sec-prefs-advanced" endterm="sec-prefs-advanced-short"/>). You are strongly advised to
+use this only on your own equipment, and only for experimentation
+purposes.
+</para>
+
</section>
</chapter>