+#~ msgid "New Film"
+#~ msgstr "Nový film"
+
+#~ msgid "Could not get video for view (%s)"
+#~ msgstr "Nemôžem získať náhľad z videa (%s)"
+
+#, fuzzy
+#~ msgid "Subtitle colours"
+#~ msgstr "Umrissfarbe"
+
+#~ msgid "Threads to use for encoding on this host"
+#~ msgstr "Thready na použitie pre enkódovanie na tomto počítači."
+
+#~ msgid "Contact email"
+#~ msgstr "Kontaktný email"
+
+#, fuzzy
+#~ msgid "Outline / shadow colour"
+#~ msgstr "Umrissfarbe"
+
+#~ msgid "Down"
+#~ msgstr "Dole"
+
+#~ msgid "Up"
+#~ msgstr "Hore"
+
+#~ msgid ""
+#~ "A few projectors have problems playing back very high bit-rate DCPs. It "
+#~ "is a good idea to drop the JPEG2000 bandwidth down to about 200Mbit/s; "
+#~ "this is unlikely to have any visible effect on the image."
+#~ msgstr ""
+#~ "Pár projektorov majú problém prehrať veľmi vysoký bit rate DCP. Je dobré, "
+#~ "aby ste nastavili JPEG2000 bandwidth na okolo 200Mbit/s; nebude to mať "
+#~ "žiadnu viditeľnú stratu obrazu. "
+
+#~ msgid ""
+#~ "All of your content is at 1.85:1 or narrower but your DCP's container is "
+#~ "Scope (2.39:1). This will pillar-box your content inside a Flat (1.85:1) "
+#~ "frame. You may prefer to set your DCP's container to Flat (1.85:1) in "
+#~ "the \"DCP\" tab."
+#~ msgstr ""
+#~ "Všetok váš obsah je Flat (1.85:1) alebo menší, ale DCP kontajner je Scope "
+#~ "(2.39:1). Toto upraví váš obsah na Flat (1.85:1). Mali by ste prestaviť "
+#~ "DCP kontajner na Flat (1.85:1) v záložke \"DCP\"."
+
+#~ msgid ""
+#~ "All of your content is in Scope (2.39:1) but your DCP's container is Flat "
+#~ "(1.85:1). This will letter-box your content inside a Flat (1.85:1) "
+#~ "frame. You may prefer to set your DCP's container to Scope (2.39:1) in "
+#~ "the \"DCP\" tab."
+#~ msgstr ""
+#~ "Všetok váš obsah je Scope (2.39:1), ale DCP kontajner je Flat (1.85:1). "
+#~ "Toto upraví váš obsah na Flat (1.85:1). Mali by ste prestaviť DCP "
+#~ "kontajner na Scope (2:39:1) v záložke \"DCP\"."
+
+#~ msgid "Log:"
+#~ msgstr "Log:"
+
+#~ msgid ""
+#~ "You are set up for an Interop DCP at a frame rate which is not officially "
+#~ "supported. You are advised to make a SMPTE DCP instead."
+#~ msgstr ""
+#~ "Nastavili ste počet snímok za sekundu (frame rate), ktoré nie Interop DCP "
+#~ "nepodporuje. Prosím, nastavte SMPTE DCP."
+
+#~ msgid ""
+#~ "You are using 3D content but your DCP is set to 2D. Set the DCP to 3D if "
+#~ "you want to play it back on a 3D system (e.g. Real-D, MasterImage etc.)"
+#~ msgstr ""
+#~ "Používate 3D obsah ale vaše DCP je nastavené ako 2D. Ak chcete DCP "
+#~ "prehrať na 3D systéme (napr. Real-D, MasterImage, atď.), prestavte DCP na "
+#~ "3D."
+
+#~ msgid ""
+#~ "You have %d files that look like they are VOB files from DVD. You should "
+#~ "join them to ensure smooth joins between the files."
+#~ msgstr ""
+#~ "Máte %d súborov, ktoré vyzerajú ako by boli VOB súbory z DVD. Mali by ste "
+#~ "ich spojiť, aby sa hladko menili."
+
+#~ msgid ""
+#~ "You have specified a font file which is larger than 640kB. This is very "
+#~ "likely to cause problems on playback."
+#~ msgstr ""
+#~ "Vybrali ste súbor s písmom, ktorý je väčší ako 640kB. Môže to spôsobiť "
+#~ "problémy pri prehrávaní."
+
+#~ msgid ""
+#~ "Your DCP frame rate (%d fps) may cause problems in a few (mostly older) "
+#~ "projectors. Use 24 or 48 frames per second to be on the safe side."
+#~ msgstr ""
+#~ "Váš počet obrázkov za sekundu (frame rate) (%d fps), ktorý ste nastavili, "
+#~ "môže spôsobiť problémy na (hlavne starých) projektoroch. Použite 24 alebo "
+#~ "48 obrázkov za sekundu (frame rate)."
+
+#~ msgid ""
+#~ "Your DCP has fewer than 6 audio channels. This may cause problems on "
+#~ "some projectors."
+#~ msgstr ""
+#~ "Vaše DCP má menej ako 6 audio kanálov. Toto môže spôsobiť problémy pri "
+#~ "prehrávaní."
+